Difference between revisions of "HP cli basics"

From Notes_Wiki
(Created page with "<yambe:breadcrumb>Switch_configuration_notes|Switch configuration</yambe:breadcrumb> =HP cli basics= ==Connect to HP switch CLI== To connect to HP switch over CLI, use: <pre...")
 
m
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
<yambe:breadcrumb>Switch_configuration_notes|Switch configuration</yambe:breadcrumb>
[[Main Page|Home]] > [[Switch configuration notes]] > [[HP cli basics]]
=HP cli basics=


=Connect and use CLI=
==Connect to HP switch CLI==
==Connect to HP switch CLI==
To connect to HP switch over CLI, use:
To connect to HP switch over CLI, use:
<pre>
<pre>
Line 11: Line 10:




==Switch to system-view similar to enable mode==
==Shift backspace to delete characters==
Instead of backspace use shift backspace to delete characters
 


To get system-view similar to enable mode use:
==Come directly to top==
<pre>
To change directly to top use Ctrl+Z
  system-view
</pre>




=Look at existing configuration=
==See port number for given MAC address using mac address table (CAM table)==
==See port number for given MAC address using mac address table (CAM table)==
To see port number for given MAC address using mac address table (CAM table):
To see port number for given MAC address using mac address table (CAM table):
<pre>
<pre>
   display mac-address AAAA-BBBB-CCCC
   display mac-address AAAA-BBBB-CCCC
</pre>
</pre>




==See port configuration==
==See port configuration==
To see configuration for an interface:
To see configuration for an interface:
<pre>
<pre>
Line 35: Line 32:
</pre>
</pre>


==See current configuration==
To see current configuration (Similar to running-config in Cisco/Dell) use:
<pre>
display current-configuration
</pre>
==See VLAN information==
To see vlan information use:
<pre>
display vlan brief
</pre>
==See routing table==
To see route use:
<pre>
display ip routing-table
</pre>
=Change configuration=
==Switch to system-view similar to enable mode==
To get system-view similar to enable mode use:
<pre>
  system-view
</pre>




==To change interface configuration==
==To change interface configuration==
To change interface configuration use:
To change interface configuration use:
<pre>
<pre>
   interface Gig 1/0/34
   interface Gig 1/0/34
   shut
   shut
</pre>
Note that any any point we can reset interface back to default settings using:
<pre>
default
</pre>
==Add new static route==
To add a new static route use below example:
<pre>
ip route-static 0.0.0.0 0.0.0.0 192.168.7.5
</pre>
</pre>




==To quit from switch completely==
==To quit from switch completely==
To quit from switch use:
To quit from switch use:
<pre>
<pre>
Line 55: Line 91:




<yambe:breadcrumb>Switch_configuration_notes|Switch configuration</yambe:breadcrumb>
 
 
[[Main Page|Home]] > [[Switch configuration notes]] > [[HP cli basics]]

Latest revision as of 07:31, 11 June 2023

Home > Switch configuration notes > HP cli basics

Connect and use CLI

Connect to HP switch CLI

To connect to HP switch over CLI, use:

   ssh admin@IP or admin1@IP

based on whether username is set as admin or admin1.


Shift backspace to delete characters

Instead of backspace use shift backspace to delete characters


Come directly to top

To change directly to top use Ctrl+Z


Look at existing configuration

See port number for given MAC address using mac address table (CAM table)

To see port number for given MAC address using mac address table (CAM table):

   display mac-address AAAA-BBBB-CCCC


See port configuration

To see configuration for an interface:

   display current interface Gig 1/0/34 


See current configuration

To see current configuration (Similar to running-config in Cisco/Dell) use:

display current-configuration


See VLAN information

To see vlan information use:

display vlan brief


See routing table

To see route use:

display ip routing-table


Change configuration

Switch to system-view similar to enable mode

To get system-view similar to enable mode use:

   system-view


To change interface configuration

To change interface configuration use:

   interface Gig 1/0/34
   shut

Note that any any point we can reset interface back to default settings using:

default


Add new static route

To add a new static route use below example:

ip route-static 0.0.0.0 0.0.0.0 192.168.7.5


To quit from switch completely

To quit from switch use:

   quit
   quit



Home > Switch configuration notes > HP cli basics