Difference between revisions of "Ip"

From Notes_Wiki
m
m
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
<yambe:breadcrumb>System_administration_tools|System Administration Tools</yambe:breadcrumb>
[[Main Page|Home]] > [[CentOS]] > [[CentOS 6.x]] > [[System administration tools]] > [[Ip|ip]]
=ip=


In newer versions of Operating Systems such as Fedora 20 or CentOS 7, older ifconfig and route commands are discontinuted.  In such operating systems the only option is to use '<tt>ip</tt>' command for obtaining network information.   
In newer versions of Operating Systems such as Fedora 20 or CentOS 7, older ifconfig and route commands are discontinuted.  In such operating systems the only option is to use '<tt>ip</tt>' command for obtaining network information.   
Line 94: Line 93:


Note that down interfaces do not communicate with external network.  But access to IP assigned to a local interface even if it is down will work.
Note that down interfaces do not communicate with external network.  But access to IP assigned to a local interface even if it is down will work.
==To change interface MTU==
To change interface MTU use:
<pre>
ip link set eth0 mtu 1400
</pre>




Steps learned from http://www.tecmint.com/ip-command-examples/
Steps learned from http://www.tecmint.com/ip-command-examples/
[[Main Page|Home]] > [[CentOS]] > [[CentOS 6.x]] > [[System administration tools]] > [[Ip|ip]]

Latest revision as of 12:08, 28 July 2022

Home > CentOS > CentOS 6.x > System administration tools > ip

In newer versions of Operating Systems such as Fedora 20 or CentOS 7, older ifconfig and route commands are discontinuted. In such operating systems the only option is to use 'ip' command for obtaining network information.


Obtaining current configuration

To look at current IP address configuration use:

ip addr show

Similarly to look at current routes use:

ip route show


Persistent IP address configuration

To configure a static IP on an interface use following steps:

  1. Created or edit '/etc/sysconfig/network-scripts/ifcfg-<interface>' file. For example for eth0 it would be /etc/sysconfig/network-scripts/ifcfg-eth0
  2. In file configure persistent IP address (DHCP or static) as follows:
    DEVICE=eth0
    BOOTPROTO=static
    IPADDR="10.0.0.2"
    NETMASK="255.255.255.0"
    GATEWAY="10.0.0.1"
    DNS1="4.2.2.2"
    DNS2="8.8.8.8"
    ONBOOT="yes"
    NM_CONTROLLED="no"
    HWADDR=<MAC-address>
  3. Then use command "systemctl restart network" to restart network service and new configuration to take effect
  4. Then use "ip addr show" to list current IP addresses in use


Persistent static route configuration

To configure persistent static routes use following steps:

  1. Created or edit '/etc/sysconfig/network-scripts/route-<interface>' file. For example for eth0 it would be /etc/sysconfig/network-scripts/route-eth0
  2. In file configure persistent static route as follows:
    10.10.1.0/24 via 10.0.0.3 dev eth0
  3. Then use command "systemctl restart network" to restart network service and new configuration to take effect
  4. Then use "ip route show" to list current routes in use


IP configuration commands

To configure IP address using commands, where the changes would be lost on machine reboot, use:

ip addr add 10.0.0.2 dev eth0

To configure static routes for current session (till next shutdown or reboot) use:

ip route add 10.10.1.0/24 via 10.0.0.3 dev eth0

To configure default route use

ip route add default via 10.0.0.1

Note that IP addresses can be removed using:

ip addr del 10.0.0.2 dev eth0

Similarly routes can be removed using

ip route del 10.10.1.0/24 via 10.0.0.3 dev eth0


To change interface state to up

To make interface up without assigning IP adddress (for capturing packets, etc.) use:

ip link set eth0 up

Similalry to make interface down without removing IP address use:

ip link set eth0 down

Note that down interfaces do not communicate with external network. But access to IP assigned to a local interface even if it is down will work.


To change interface MTU

To change interface MTU use:

ip link set eth0 mtu 1400


Steps learned from http://www.tecmint.com/ip-command-examples/


Home > CentOS > CentOS 6.x > System administration tools > ip