Difference between revisions of "Switch configuration notes"
From Notes_Wiki
m |
m |
||
| (18 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Main Page|Home]] > [[Switch configuration notes]] | |||
==Cisco network switches== | ==Cisco network switches== | ||
| Line 22: | Line 21: | ||
*[[Configure DHCP relay in Cisco nexus switches]] | *[[Configure DHCP relay in Cisco nexus switches]] | ||
*[[Configure VPC between two Cisco Nexus switches]] | *[[Configure VPC between two Cisco Nexus switches]] | ||
*[[Solving IP ROUTE TABLE Overflow issue on Linksys Cisco SMB SG series switches]] | |||
==Juniper devices== | ==Juniper devices== | ||
*[[Basic configuration of juniper device]] | *[[Basic configuration of juniper device]] | ||
*[[Analyzing traffic on juniper switches]] | |||
*[[Capturing packets on juniper switches]] | |||
*[[Configuring new Juniper switch for remote access via vme port]] | |||
*[[Trunking incoming VLANs on uplink port to all other ports]] | |||
| Line 33: | Line 37: | ||
*[[Enable http interface on HP5100 series switches]] | *[[Enable http interface on HP5100 series switches]] | ||
*[[HP A5500 switch password reset and finding IP through console]] | *[[HP A5500 switch password reset and finding IP through console]] | ||
*[[Configure stacking on Aruba 2930F switches]] | |||
*[[Configure lacp or port-channel on Aruba switches (Trunk)]] | |||
| Line 39: | Line 45: | ||
*[[Upgrade OS or firmware in Dell N4032 switch]] | *[[Upgrade OS or firmware in Dell N4032 switch]] | ||
*[[Dell 4820T or S3100 hybrid ports]] | *[[Dell 4820T or S3100 hybrid ports]] | ||
*[[Configure VLT between two Dell S4128T-on or S4128F-on switches]] | |||
*[[Configuring port mirroring or monitor session on Dell OS 10 switches]] | |||
*[[Configuring new S4100 series Dell switch with OS 10]] | |||
*[[Upgrading firwmare on S4100 series Dell switches with OS 10]] | |||
*[[Breaking 40G QSFP+ to 4x10G SFP+ in Dell OS 10 switches]] | |||
*[[Get Dell OS 10 switch service tag using cli]] | |||
==Netgear network switch== | |||
*[[Stacking netgear switches]] | |||
| Line 45: | Line 61: | ||
==Cisco routers== | ==Cisco routers== | ||
*[[Reset enable password on cisco router]] | *[[Reset enable password on cisco router]] | ||
*[[Cisco CSR V1000 virtual router]] | |||
*[[Configure Cisco router outgoing PAT or overload NAT for users to access Internet]] | |||
*[[Configure DHCP server on Cisco router]] | |||
*[[Configure basic BGP on Cisco router]] | |||
*[[Reset configuration of Cisco router]] | |||
| Line 76: | Line 96: | ||
*[[Configure VLT and DCB across two Dell MXL 10/40GbE chassis switches]] | *[[Configure VLT and DCB across two Dell MXL 10/40GbE chassis switches]] | ||
*[[Stacking Dell 10/40GbE MXL switches]] | *[[Stacking Dell 10/40GbE MXL switches]] | ||
[[Main Page|Home]] > [[Switch configuration notes]] | |||
Latest revision as of 04:10, 10 April 2024
Home > Switch configuration notes
Cisco network switches
- Reset enable password on Cisco switch
- Upgrading Cisco switch IOS using tftp server
- Loading IOS on Cisco switch which has no existing IOS
- Tracing physical location of IP address in network using switches
- Configuring etherchannel on Cisco switches
- Configuring privilege levels on Cisco switch
- Configuring storm control on Cisco switch
- Simple Cisco switch commands, tips and tricks
- Enabling SSH and disabling telnet to Cisco switch
- Shifting Linksys switch to management VLAN 2
- Configuring basic Access Control List (ACL) on Cisco switches
- Mirroring ports on Cisco switches
- Configuring manageable switch port to behave as unmanageable switch port
- Spanning tree configuration for Cisco switches
- Configuring cisco switch as SNMP server
- Determining the cause for err-disabled port
- Configure time-zone for Cisco switch
- Configure DHCP relay in Cisco nexus switches
- Configure VPC between two Cisco Nexus switches
- Solving IP ROUTE TABLE Overflow issue on Linksys Cisco SMB SG series switches
Juniper devices
- Basic configuration of juniper device
- Analyzing traffic on juniper switches
- Capturing packets on juniper switches
- Configuring new Juniper switch for remote access via vme port
- Trunking incoming VLANs on uplink port to all other ports
HP Network switches
- Configure new HP 2530 switch
- HP cli basics
- Enable http interface on HP5100 series switches
- HP A5500 switch password reset and finding IP through console
- Configure stacking on Aruba 2930F switches
- Configure lacp or port-channel on Aruba switches (Trunk)
Dell network switch
- Configuring Dell N4032 switch in stack mode
- Upgrade OS or firmware in Dell N4032 switch
- Dell 4820T or S3100 hybrid ports
- Configure VLT between two Dell S4128T-on or S4128F-on switches
- Configuring port mirroring or monitor session on Dell OS 10 switches
- Configuring new S4100 series Dell switch with OS 10
- Upgrading firwmare on S4100 series Dell switches with OS 10
- Breaking 40G QSFP+ to 4x10G SFP+ in Dell OS 10 switches
- Get Dell OS 10 switch service tag using cli
Netgear network switch
Routers
Cisco routers
- Reset enable password on cisco router
- Cisco CSR V1000 virtual router
- Configure Cisco router outgoing PAT or overload NAT for users to access Internet
- Configure DHCP server on Cisco router
- Configure basic BGP on Cisco router
- Reset configuration of Cisco router
SAN switch
Cisco SAN switch
- Configuring Cisco MDS 9124 fiber switch for SAN
- Resetting password for MDS 9124 switch
- Configuring Cisco MDS 9148S 16G 48 FC SAN switch with multipath for HA
- Upgrade OS on Cisco SAN switch
- Upgrade license on Cisco SAN switch
Brocade storage switch
- Brocade storage switch management IP configuration
- Configuring brocade switch for SAN zoning
- Configure Brocade storage switch to send logs to syslog
- Troubleshoot Brocade SAN switch disable on boot issue
Converged or unified switches
Cisco UCS switch
- Convert ports from network to storage on Cisco UCS unified fabric switch
- Configure VLT and DCB across two Dell MXL 10/40GbE chassis switches
- Stacking Dell 10/40GbE MXL switches
